Horizontal Centrifugal Pumps for Agricultural and Rural Water Supply are subject to mandatory BIS ISI certification under the Pumps (Quality Control) Order, 2026. From 6 mo after publication of the QCO in the e-Gazette, these products cannot be lawfully manufactured for sale, imported, or distributed in India without a valid BIS ISI licence under IS 6595 (Part 1):2018. Non-compliance attracts penalties under the BIS Act, 2016 — product seizure, fines, and prosecution.
This guide covers the applicable Indian Standard, key technical and safety requirements, the step-by-step certification process, documentary requirements, and the most common compliance pitfalls for manufacturers and importers.
📜 Applicable Indian Standard
- IS 6595 (Part 1):2018 — Horizontal Centrifugal Pumps for Agricultural and Rural Water Supply (primary standard)
- Aligned with the corresponding IEC / ISO standard for technical performance and safety
- Latest amendments notified by BIS apply automatically
📌 These are India's most widely used farm pumps. The QCO enforces minimum hydraulic performance, efficiency, and endurance — preventing low-quality pumps from undermining farmer water access and government rural water programmes.
🔬 Key Quality Requirements Under IS 6595 (Part 1):2018
BIS-approved laboratories evaluate the following during type testing:
Hydraulic Performance
Head, discharge, and efficiency at rated operating point. Performance curve compliance per IS 6595-1 charts.
Motor-Pump Integration
Coupling alignment, shaft endurance, and integrated-set vibration limits. Insulation and earthing on motor.
Endurance Testing
Continuous-duty testing at rated load for prescribed hours. Bearing and seal life within IS 6595-1 limits.
Marking & Identification
Rated discharge, head, kW, RPM, and motor details. ISI Mark plus licence number on pump nameplate.
Products covered under IS 6595 (Part 1):2018:
- Single-stage horizontal centrifugal pumps for agricultural irrigation
- Rural drinking-water pumps for PHE and Jal Jeevan use
- Canal-side and pond pumps for surface water lifting
- Coupled motor-pump sets supplied as a single unit
📋 Step-by-Step BIS ISI Certification Process
- Scope Mapping (Part 1 vs Part 2)Confirm the pump is marketed for agricultural / rural use under Part 1 — not general use under Part 2. Mis-classification leads to test-report mismatches.
- Application FilingSubmit online application on manak.bis.gov.in. Indian manufacturers via Product Certification Scheme; foreign manufacturers via FMCS.
- Sample TestingSubmit complete coupled sets to a BIS-recognised pump testing laboratory. Hydraulic, efficiency, and endurance tests: approximately 4–6 weeks.
- Factory InspectionBIS officers inspect pump casting, machining, motor assembly, and in-house testing capability.
- Licence GrantBIS issues the ISI Mark licence. ISI Mark plus licence number is applied on the pump nameplate.
- Surveillance & RenewalPeriodic BIS market sample testing, factory audits, and annual marking fees keep the licence active.
📄 Documents Required
- Company incorporation / registration certificate
- Product list with kW rating, head, discharge
- Pump and motor engineering drawings and BOM
- Process flow chart for casting, machining, and assembly
- In-house testing capability details
- Quality Manual / ISO 9001 certificate (if available)
- AIR appointment letter (for foreign manufacturers)
- Existing test reports from BIS-recognised labs (if any)
⚠ Common Compliance Pitfalls
Common issues include hydraulic performance below rated curves, efficiency shortfall, excessive vibration from coupling misalignment, and missing nameplate marking under IS 6595 (Part 1).
🏭 Special Considerations for Importers
Imported pumps targeting India's rural and agricultural market must hold valid BIS ISI certification under Part 1. Government and state-subsidy schemes require ISI marking as a vendor empanelment prerequisite.
Get BIS Certified — We Handle Everything
Global Approbation manages end-to-end BIS ISI / FMCS registration for Horizontal Centrifugal Pumps (Agri & Rural) — from documentation to licence grant. Enforcement begins 6 mo from QCO notification.
BIS ISI / FMCS Services Talk to Our Team