BIS Certification for Low-Speed Food Grinding Machines in India products are subject to mandatory BIS Compulsory Registration Scheme (CRS) requirements in India. Every manufacturer and importer must obtain a valid BIS CRS registration for each model before the product can be manufactured, imported, or sold in the Indian market. Non-compliance attracts penalties including product seizure, market withdrawal, and prosecution under the BIS Act 2016.
This guide covers the applicable Indian Standards, mandatory safety testing requirements, the step-by-step CRS registration process, documentary requirements, and the most critical compliance pitfalls for this product category in 2026.
📜 Applicable Indian Standards
The following Indian Standards apply to this product category under the BIS CRS framework:
- IS/IEC 60335-2-14 — Particular requirements for kitchen machines (covers low-speed food grinding and juicing machines)
- IS/IEC 60335-1 — General requirements for safety of household and similar electrical appliances
- IS 13252 (Part 1) — Indian adaptation of IEC 60335-1
📌 Low-speed grinding machines operate at significantly higher torque than high-speed blenders, making motor protection under jam conditions more critical. Despite low RPM, the rotating auger or grinding element exerts sufficient force to cause serious injury. BIS testing evaluates auger access from the feed chute, the torque-limited jam protection system, and motor endurance under continuous cold-press juicing loads.
🔬 Mandatory Safety Tests
BIS-approved laboratories evaluate the following key areas during safety testing for this product category:
Electrical Safety
Insulation resistance, dielectric strength, leakage current, earth continuity, and motor protection circuit.
Feed Chute Access Prevention
Test probe access to the slow-rotating auger from the feed chute aperture; compliance with IS/IEC dimensional access limits despite low RPM.
Torque-Limited Jam Protection
Motor thermal cut-out or torque-limiter actuation when auger is jammed by a hard food item; re-start safety after jam resolution.
Motor and Drive Endurance
Motor performance under continuous cold-press juicing loads; gear reduction drive endurance and thermal stability during rated operation.
📋 Step-by-Step BIS CRS Registration Process
- Auger Speed ClassificationConfirm the machine operates below the RPM threshold that differentiates low-speed grinders from standard-speed kitchen machines under IS/IEC 60335-2-14. This affects the applicable access probe test.
- Appoint AIRForeign manufacturers must appoint an AIR in India before filing the BIS CRS application.
- Sample TestingSubmit representative machines to a BIS-approved lab. Low-speed food grinder testing typically takes 4-6 weeks.
- Online ApplicationSubmit Form VI, test report, factory documents, photographs, trademark certificate, and AIR letter on BIS Manak Online.
- BIS Query ResolutionCommon queries involve auger access probe measurements at low speed, jam-protection actuation data, and motor endurance documentation.
- R-Number GrantBIS issues the R-number upon approval. Mark on the appliance, packaging, and user manual.
- RenewalValid for 2 years. Changes to auger, feed chute, motor, or jam protection system require re-testing.
📄 Documents Required
- Completed BIS Form VI and declaration of conformity
- Test report as per IS/IEC 60335-2-14 and IS 13252 (Part 1) from BIS-approved laboratory
- Factory registration and address proof
- Trademark registration certificate
- AIR appointment letter (for foreign manufacturers)
- Product photographs with compliance label placement
- Technical specification sheet (rated voltage, motor power, auger RPM, juicing/grinding capacity)
- User manual in English and/or Hindi
⚠ Common Rejection Reasons
Common rejection causes include the feed chute aperture dimensions allowing a test probe to contact the auger even at low speed, jam-protection system failing to actuate within the specified time or torque limit when the auger is blocked by a hard food item, motor winding temperature exceeding the rated rise limit during the continuous cold-press endurance test, and model number discrepancies between the test report and the BIS registration application.
🏭 Special Considerations for Importers
Low-speed food grinding machines and cold-press juicers are imported for premium health food retailers, gyms, and direct-to-consumer e-commerce in India. Every model requires a separate valid BIS CRS registration before customs clearance.
Low-Speed Food Grinder BIS Certification Partner
Global Approbation manages BIS CRS registration for low-speed food grinding machines and cold-press juicers — from IS/IEC 60335-2-14 testing to R-number grant.
BIS CRS Services Talk to Our Team